ComAp

• Interface to PV inverters in Hybrid applications
• Connection to MTU MIP4000
• Collection of data from Modbus RTU/TCP device(s) and transmission of this data to WebSupervisor
• Predefined communication settings for devices.

• Protection relay for on-grid applications like generator sets, renewable energy sources,
cogeneration, micro turbines, etc.
• Adjustable voltage, frequency and loss of mains protections to protect both the distribution network
and the generators
• True RMS measurement
• Vector Shift and Rate of change of frequency
(ROCOF) protection in one unit
• Voltage symmetrical components evaluation for
better detection of voltage asymmetry failures

• Communication module that allows connection of a single controller as well as to the Internet or Local area network.
• Connection to the Internet can be achieved via built-in cellular modem supporting 2G, 3G and 4G (LTE) networks or Ethernet cable.
• The built-in GPS receiver also enables location and tracking of the device via WebSupervisor.
• Wired Internet connection via ethernet port
• Wireless Internet connection via integrated
2G/3G/4G(LTE) cellular modem

• 12,1″ Capacitive Touch Screen with resolution 1280 x 800 px
• Industrial and robust design
• Rugged housing manufactured from a piece of aluminium alloy
• Temperature range from -30 to +70° C
• Chemically strengthened front glass (8 x as strong as normal glass)

• 5,7” Colour TFT Display with a resolution of 320 × 240 pixels.
• Plug and play operation
• Direct connection to the controller (converters not needed).
• Communication connection via RS-485.
• Same language support as the controller including graphic languages.

• Plug and play operation (auto configuration)
• Simple, fast and intuitive control
• Easy drag and drop screen configuration in graphical editor
• Fast access to important data
• Five configurable soft keys

• Full gen-set control with interface to PV inverters
• Inbuilt power management and load sharing
• Protection against gen-set underloading
• Dynamic spinning reserve calculation for maximized fuel savings
• Support of up to 100% renewable energy penetration

• Comprehensive paralleling gen-set controller
• Parallel operation up to 32 gen-sets
• High level control for complex systems
• CHP and gas engine controller
• Single or multiple gen-sets in parallel to mains operation with automatic back up function, multiple island operation

• Synch check, over/undervoltage and reverse power protection in one unit
• Over/underfrequency, Instantaneous overcurrent, IDMT overcurrent and Earth Fault protection as optional features
• Extensive flexibility for various applications through functions
• 3 phase voltage and current measurement
• Breaker failure protection and battery voltage protection

• Voltage, frequency and current based protections for on-grid distributed power generation
• True RMS measurement
• 3-phase voltage and current measurement
• Optional functions for extended protection
• Assignment of 8 Binary inputs, 9 Binary outputs, 3 Analog inputs

• Comprehensive switchgear controller
• Built-in control for up to 32 logic groups divided by Bus Tie Breakers
• High level control for complex systems
• Built-in breaker control
• Genset group synchronization, Loadsharring and VArsharring via CAN2

• Single gen-set controller for Prime-power applications
• Direct communication with EFI engines
• Total remote monitoring and control
• Internal PLC support with PLC editor and monitor included in LiteEdit
• Cloud-based monitoring and control

• Single gen-set controller for Stand-by and Primepower applications
• Direct communication with EFI engines
• Total remote monitoring and control
• Internal PLC support with PLC editor and monitor included in LiteEdit
• Cloud-based monitoring and control via WebSupervisor

• Comprehensive paralleling gen-set controller
• Parallel operation up to 32 gen-sets
• High level control for complex systems
• Support of wide range of applications
• Single or multiple gen-sets in parallel to mains operation with automatic back up function, multiple island operation

• Comprehensive gen-set controller for both single and multiple gensets operating in standby or paralleling modes
• To be used in conjunction with detachable colour displays InteliVision 5 or InteliVision 8
• Support of engines with ECU (Electronic Control Unit)
• Complete integrated gen-set solution and signal sharing via CAN bus – minimum external components needed
• Many communication options –remote supervising and servicing

• The InteliDrive Panel is complete controller solution designed for immediate use with minimalrequirements for installation and configuration
• The panel includes a powerful but easily configurable and userfriedly controller InteliDrive IPC and all other components necessary for control industrial applications.
• There are used industry standard Deutsch connectors that allow easy connection of the simplest mechanical engines and the latest fully electronic engines.
• The controller is fully configurable from the front user interface or PC configuration tool.
• The InteliDrive panel is available in two rugged eclosures – metal and polycarbonate.

• Comprehensive switchgear controller
• Built-in control for up to 32 logic groups divided by Bus Tie Breakers
• High level control for complex systems
• Built-in breaker control
• Genset group synchronization, Loadsharring and VArsharring via CAN2

• Fuel measurement and statistics for OPEX evaluation and battery bank maintenance
• Four additional analogue inputs; One analog output (with optional lL-NT-AIO plug-in module)
• Remote monitoring and control for optimal service intervals, fault monitoring and reduced operating expenditure
• Various communication options (Airgate, WebSupervisor, GSM/SMS, GPRS, Ethernet, Alarm emails, SNMP v1) by using optional extension modules
• Full gen-set monitoring and protection

• Stand-alone digital speed governor for gas gensets
• Wide range of supported actuators within one hardware
• Precise throttle position control, with optional position feedback utilization
• Different modes of control – over Binary signals, over Analogue signals, over CAN line (with specific ComAp controllers and firmwares)
• Load dependent PID adjustment possibility for variable load applications (e.g. Oil&Gas industry)